Overview:
Pinhole photography is arguably the most basic form of photography available. Why? Because it doesn’t require a lens. Instead, the light from a scene passes through a tiny hole into a dark area containing a sensor of some sort. The most basic pinhole cameras have been as simple as box with a hole in which light passes through and exposes a strip of film or photo paper.
The beauty of pin hole cameras is in the ease of simplicity. There is no lens to deal with. No focus or depth of field to manage. The size of the pinhole is the aperture and cannot be changed. The only functions that you have control over are shutter speed, and ISO. If you’re just using a film camera, chances are that the only control you can control is the shutter speed.
That being said, pinhole cameras do have disadvantages and have certain ‘looks’ to them. Generally, images from pinhole cameras are ‘softer’ than images taken with lenses, meaning that the details of the image are harder to make out. Furthermore, because of the inherent small size of the pinhole (acting as an aperture), shutter speeds of a second or greater are commonly used, thus requiring stabilization such as a tripod. Below is an image of the most basic pinhole and how they function:
![]() |
| http://www.optics4kids.org/osa.ok4/media/optics4kids/tutorials/images/fermat03.gif |
Methods:
There are many ways to make pinhole cameras ranging from extremely simple, hole-in-box-type-things to the more complex canisters with film coating the inside, to even rooms that act as pinhole cameras. For mine, I simply used my DSLR camera and a modified body cap to create a pinhole effect. This allows for images to be recorded onto the sensor, and immediate playback to occur so that you can refine your exposure and composition, and shoot again. Some can be made with simply taping over the exposed sensor of your camera, but I preferred to use the body cap so that it formed a tight fit and didn't leak any light from the sides.
Materials needed:
- DSLR camera
- Body cap for the DSLR camera (found here:
- Tripod
- duct tape
- device to puncture the tape with
- Drill
First, I took my body cap and drilled a hole directly in the center using a wood drill bit. The hole is roughly 1cm in diameter. Be sure not to make it too large, or too small. It will be covered by tape anyways, but it may ruin the integrity and function of the body cap. Once done drilling, make sure to file down the edges or clear off any debris that may have been created, as this debris may be able to damage or pollute your sensor with dust.
This is what it should appear like.
Once done, cut the duct tape up into small squares large enough to cover the drill hole with, and apply a square of duct tape. I preferred to poke the hole while the duct tape was on a hard surface so that I could be more precise with the size.
Apply the duct tape once you puncture a hole of some size. Sewing needles work best, but all I had on hand was a thumb tack. When you’re done, you should have a very small hole, like in the image below. It’s hard to see, but in the center of the lens there is light passing through from the other side. Make sure that the hole is as rounded and smooth as possible. If the edges are rough, it may affect the image quality.
My ghetto-rigged digital pinhole camera. (note, when you’re applying the body cap/tape, be careful not to expose your camera to excessive amounts of dust or leave your sensor exposed for too long.).
Techniques:
Now that the construction is done, you can begin experimenting with the pinhole camera. First, there are a few things that you should understand about the way they function:
- They are lensless. What this means is that there is no focus required.
- Aperture is dictated by the size of the hole in the duct tape
- The smaller the hole, the sharper the image and the more that will be in focus
- The larger the hole, the softer the image and the less focused
- You can change the size of the hole in the duct tape by puncturing different size holes with different tools. Try paper clip, sewing needles, thumb tacks, etc.
- You will not be able to see through the viewfinder, and instead have to ‘guess-and-check’ your photos.
- Because you are not able to see through the viewfinder, the focal length and field of view is always unknown. (dictated by some very complex calculations). Guess and check is your friend.
- You’ll get many people giving you weird looks. Some will be brave enough to tell you that you have the lens cap on.
Low light conundrum: The most important thing to understand about pinhole cameras is that the pinhole is the aperture. Because the pinhole is so tiny, it is equivalent to the smallest apertures of lenses, such as f/64 and smaller. As a result, less light will be entering the camera and hitting your sensor to expose the image. To counteract this, there are a number of things you can do.
GOLDEN RULE: Use a tripod! This is a must. Indoors I frequently used shutter speeds of 5 seconds or over. Even outdoors, I was using shutter speeds of 1/10th a second or slower in some instances. Other things you can do are:
- Use a slower shutter speed to allow for more light.
- Increase your ISO.
- Increase the size of your pinhole (this comes at the cost of image sharpness)
Examples: Below are a few samples of my attempts at pinhole photography, and a description of the learning that occurred.
ISO 800. 1/8th second. Largest Pinhole size.
For the first images, I tried to utilize the body cap without any tape on it to see what the effect might be, and use the size of the opening as a reference for pinhole size. As you can see, the large hole caused the image to be entirely soft, and not at all in focus or defined. It appears to be more like the conventional bokeh than an image.
ISO 800, 13 seconds. Medium Pinhole.
This is the exact same shot as the one above it, however for this one, I used a medium sized pinhole (roughly 1mm in diameter). As you can see, its much more defined and we can make out the subject more clearly. However, since the hole was smaller I had to utilize a shutter speed of 13 seconds versus the relatively fast 1/8th second in the previous image.
ISO 800, 1/160th second. Medium sized pinhole.
This was the second picture I took with the medium sized pinhole. Since it was outdoors and there was plenty of light available, I was able to use a fast shutter speed and relatively low ISO of 800. The pinhole is still too large to get a completely sharp image, contributing to the extreme softness of the photograph, but I kind of liked the dreamy-look.
ISO 800, 5 seconds. Small sized pinhole.
I refined the size of my pinhole to be smaller (roughly .5mm in diameter) and snapped this picture. Since it was smaller, I had to utilize a shutter speed of 5 seconds, mounted on a tripod. Notice how a smaller pinhole results in more defined/sharper images. Getting closer!
This is the smallest pinhole size that I utilized. Being able to use a smaller sized pinhole would require more precise tools and different methods, such as using a medium like tinfoil or something else that would allow for even finer control of the hole size.
ISO 3200. 13 seconds. Small pinhole size.
Success! Now that I had a small pinhole size (the smallest I would utilize in this blog), I could begin to take more detailed pictures of things. Since it was the smallest pinhole size I used, I had to increase my ISO to 3200, as well as utilize insanely slow shutter speeds still.
ISO 3200. 10 seconds. Small pinhole size.
ISO 3200. 15 seconds. Small pinhole size.
And, using long exposures coupled with softer than normal images can be fun. I pretended to be a ghost.
![]() |
| http://krisdedecker.typepad.com/photos/uncategorized/2008/04/23/pinhole_old_barn_by_integrity_of_li.jpg |
Personal Experience: Playing with pinholes was great fun, and throughout the process I definitely improved and learned how to embrace the simplicity and guess and check methods that are necessary. The greatest challenge to me was not being able to see through the viewfinder to compose the shot. Instead, I had to embrace the guess-and-check method, and spend more time refining my composition by intuition rather than by observation. Rather than look at a scene to compose properly, I found myself looking for good light instead. Another challenge that was evident was making sure that the size of the pinhole was small enough. Although I managed to create one quite small, I feel as if it isn’t completely representative of what is possible with pinhole cameras. In the future, I’d like to try more advanced techniques with pinholes, as well as to utilize other methods to be able to make my pinhole smaller, and thus, images more defined.
So, what are the advantages of pinhole cameras and photography? First of all, they are incredibly simple and can teach the very basics of optics and photography. For professional or more advanced uses, when done correctly they also offer depth of field and sharpness unparalleled by most lenses. Lastly, their simplicity is incredibly appealing. It was a relief to forget all of the basic photography and compositional rules while using pinhole cameras. Simply point, shoot, and see what happens.
I had a lot of fun experimenting with the different pinhole methods, and, although I just barely scratched the surface of what’s possible, there are many more techniques that you can delve into if that inspires you. I can’t say I’ll be doing this very often, but, experimenting with cameras and techniques is often a great way to jumpstart you’re creativity and inspiration for all aspects of photography.









No comments:
Post a Comment